Apple**胶 Technomelt PA 6818

Apple**胶 Technomelt PA 6818 PRODUCT DESCRIPTION Technomelt PA 6818 provides the following product characteristics: Technology : Polyamide Product Type : Hotmelt Cure : Physical setting Condition : Thermoplastic Components : One component Application : General assembly Appearance : Amber Application Areas: Technomelt PA 6818 is used for molding application. It has high softening point and suitable for porous substrates such as paper, wood and leather. polyamide adhesive - nourde adhesives Technical Data: Softening point : 206~216℃ Melting Viscosity at 235℃, mPas : 4000~7500 Elongation, % : 300 Application: Application Temperature: 225 to 240℃ Application System: Hotmelt application systems When bonding to a substrate with high thermal conductivity the use of a specific application temperature is required for good wetting. Do not heat the product above the specified application temperature range. When the product is not in use do not apply heat, this will degrade the quality of the product and in extreme cases cause carbonisation. The standby temperature for the product is approximately 50℃ below the application temperature, but not for longer than 72 hours. Technomelt PA 6818 may absorb moisture from the air. This will not be apparent in the solid form, but may cause bubbles on heating and could affect the bond quality. It is important, therefore, that containers are kept closed and sealed when not in use. Cleaning: Carbonised and set (non thermoplastic) material must be removed mechanically. Removal of the thermoplastic material from the hot apparatus can be achieved with solvent free cleaning system. Classification: Please refer to the corresponding safety data sheets for details on: Hazardous Information Transport Regulations Safety Regulations Storage: When properly stored in a cool, dry location, with the container tightly closed when not in use, this product will have a shelf life of at least 24 months. nourde low pressure molding material solutions ADDITIONAL INFORMATION Disclaimer: The information provided herein, especially recommendations for the usage and the application of our products, is based upon our knowledge and experience. Due to different materials used as well as to varying working conditions beyond our control we strictly recommend to carry out intensive trials to test the suitability of our products with regard to the required processes and applications. We do not accept any liability with regard to the above information or with regard to any verbal recommendation, except for cases where we are liable of gross negligence or false intention. This datasheet replaces all former versions. Reference 0.0 Technomelt PA 6818

Technomelt PA 6818


PRODUCT DESCRIPTION
Technomelt PA 6818 provides the following product characteristics:
Technology : Polyamide
Product Type : Hotmelt
Cure : Physical setting
Condition : Thermoplastic
Components : One component
Application : General assembly
Appearance : Amber


Application Areas:
Technomelt PA 6818 is used for molding application. It has
high softening point and suitable for porous substrates such as
paper, wood and leather.
polyamide adhesive - nourde adhesives


Technical Data:
Softening point : 206~216℃
Melting Viscosity at 235℃, mPas : 4000~7500
Elongation, % : 300


Application:
Application Temperature: 225 to 240℃
Application System: Hotmelt application systems


When bonding to a substrate with high thermal conductivity the use of a specific application temperature is required for good wetting.


Do not heat the product above the specified application
temperature range.


When the product is not in use do not apply heat, this will degrade the quality of the product and in extreme cases cause carbonisation. The standby temperature for the product is approximately 50℃ below the application temperature, but not for longer than 72 hours.


Technomelt PA 6818 may absorb moisture from the air. This will not be apparent in the solid form, but may cause bubbles on heating and could affect the bond quality. It is important, therefore, that containers are kept closed and sealed when not in use.




Cleaning:
Carbonised and set (non thermoplastic) material must be
removed mechanically. Removal of the thermoplastic material
from the hot apparatus can be achieved with solvent free
cleaning system.
Classification:
Please refer to the corresponding safety data sheets for details
on:
Hazardous Information
Transport Regulations
Safety Regulations


Storage:
When properly stored in a cool, dry location, with the container
tightly closed when not in use, this product will have a shelf life
of at least 24 months.
nourde low pressure molding material solutions


ADDITIONAL INFORMATION


Disclaimer:
The information provided herein, especially recommendations
for the usage and the application of our products, is based
upon our knowledge and experience. Due to different materials
used as well as to varying working conditions beyond our
control we strictly recommend to carry out intensive trials to
test the suitability of our products with regard to the required
processes and applications. We do not accept any liability with
regard to the above information or with regard to any verbal
recommendation, except for cases where we are liable of
gross negligence or false intention.
This datasheet replaces all former versions.